Repairing your wood skimboard=(

[Jim Gordon]

There has been a lot of woodboards getting major damage riding on rails. And it seems like no one knows how to fix them, including me. I used epoxy, which you can get at any hardware store. I have repaired lots of surfboards, foam skims and also aircraft. But this was a new one to me, because this type of ding was rare until guys started riding rails. So I went to work, first I took a used old wood skim and similuated an end pipe rail damage. Which is the most common type of rail damage (large sharp rocks can also cause this). This repair should work for most brands of woodskims. I'm not 100% sure, it would be your call on using this type of repair. It came out better than I though, of course it doesn't look like new. But at least it's now skimable, hope this helps you guys get your damaged boards back into the water. If you have any questions, I waiting.........

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2228.jpg

We first hit the board on the side of the black pipe, it only left a black mark.

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2230.jpg

But when we hit the sharp edge........well you can see what happened.

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2234.jpg

If there is sand or dirt in the ding, it must come out. You can use a water hose, but then you would need to use a hair dryer on it. The wood must be 100% dry before you epoxy it back together. Also you can use a razor blade to clean it out. If the outside skin chips off, bring it home, so you can put it back on. It will make the repair easier and look better. Unlike a fiberglass repair where you cut the damage part off, I have found that for a woodskim, it's best to put as much back as you can.

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2236.jpg

If you noticed I did not remove a lot of wood.

[Jim Gordon]

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2237.jpg

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2238.jpg

I just worked the epoxy in and around the wood before I C-clamped it down.

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2239.jpg

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2242.jpg

I then unclamped it so I could wipe off the excess resin, and then reclamped it and it dry over night. I should have used wax paper under the C-camp, because it stuck a little. Like I said, this should work for any brand woodskim. If you have a ding this bad, what do you have to lose. I almost forgot if you use epoxy, just use "rubbing alcohol "for cleanup.

[Jim Gordon]

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2246.jpg

http://i174.photobucket.com/albums/w113/J-gordon/IMG_2257.jpg


??

i have found that bondo also works really well for stuff like this, but it is very ugly... say you lost that peice of wood that chipped up, i would fill it with bondo if i was being lazy.

other than that, this repair job is pretty amazing.

Yes bondo is very ugly, you can make your own bondo that's clear. Just take any kind of resin, cut up any kind of fiberglass into very small pieces and mix it with the resin, and add hardener. It makes the resin strong and thick, and it comes out clear, not black/gray.

I'm still hearing guys riding rails without a cross pipe. Besides damaging their boards, they are now getting their toes and fingers caught in the end pipes. If you're not sure what an end pipe is, here's a pix of a rail with an end pipe. This rail has only one, but I think you should put one on both ends. Anyway check out the pix.

http://i174.photobucket.com/albums/w113/J-gordon/DSCF0021-1.jpg

http://i174.photobucket.com/albums/w113/J-gordon/DSCF0019-1.jpg

[sandsurfngbomber]

damn dude...on that last pic u cant even notice it

j-gordon ur my hero

[High]

you make boards also correct?

[George Bush]

I dont flatland but that is sick.

[Jim Gordon]

you make boards also correct?

Not only do I make boards, I can really f#ck them up too........;)

[Jim Gordon]

We first hit the board on the side of the black pipe, it only left a black mark. But when we hit the sharp edge........well you can see what happened.

[Jim Gordon]

If you noticed I did not remove a lot of wood. I just worked the epoxy in and around the wood before I C-clamped it down. I then unclamped it so I could wipe off the excess resin, and then reclamped it and it dry over night. I should have used wax paper under the C-camp, because it stuck a little. Like I said, this should work for any brand woodskim. If you have a ding this bad, what do you have to lose.

[Jim Gordon]

I almost forgot if you use epoxy, just use "rubbing alcohol "for cleanup.

[Billagan]

Thanks Gordon, I dont use a wood skim but I sure wish there was a lot more threads like this on here. Good information!

[amosb72]

You destroyed that board jim
nice job

oh and plus# for the info

[Jim Gordon]

You destroyed that board jim
nice job

oh and plus# for the info

It's not destroyed........I fixed it, it just doesn't look as good anymore.;)

[BART]

i nominate this thread for FAQ

[narwhal]

This is the sort of stuff Skimonline is made for.

Great job, Jim.

[Jim Gordon]

Thanks guys, just want to give something back....=)

[raj]

next time you should try wood filler!
jk
but thats awesome that you fixed that well. you can barely see the damage.

[hobo]

Thanks guys, just want to give something back....=)
about time you ungrateful POS whats it been like 20 years before you gave something back to skimboarding?

just kidding youve done atleast 532532532532x than i have, +1

[Indy]

Wouldn't it be less time consuming to go chop down a tree and make a new plank to ride on?

[derc a der]

very good. i also nominate this thread for FAQ.

[zeus]

so awesome jim

[Mapdash]

i nominate this thread for FAQ

definitely.

[Jim Gordon]

Here's a few more things, if there is sand or dirt in the ding, it must come out. You can use a water hose, but then you would need to use a hair dryer on it. The wood must be 100% dry before you epoxy it back together. Also you can use a razor blade to clean it out. If the outside skin chips off, bring it home, so you can put it back on. It will make the repair easier and look better. Unlike a fiberglass repair where you cut the damage part off, I have found that for a woodskim, it's best to put as much back as you can.

[Jim Gordon]

about time you ungrateful POS whats it been like 20 years before you gave something back to skimboarding?

just kidding youve done atleast 532532532532x than i have, +1

Hobo, who the hell do you think you are? I'm coming down there to kick your ass. Oh wait....... white writing.......:o hobo you're the best, thanks!

[Warriors]

a must read for woodboarders.

[dukiedude13]

dude, props. thats a nice job well done there.

[LMSkim]

cool jim

[RexSkimmer]

j-gordon: SOMB's man of wisdom

[skrobo]

next time you should try wood filler!
jk

??

i have found that bondo also works really well for stuff like this, but it is very ugly... say you lost that peice of wood that chipped up, i would fill it with bondo if i was being lazy.

other than that, this repair job is pretty amazing.

[Jim Gordon]

??

i have found that bondo also works really well for stuff like this, but it is very ugly... say you lost that peice of wood that chipped up, i would fill it with bondo if i was being lazy.

other than that, this repair job is pretty amazing.

Yes bondo is very ugly, you can make your own bondo that's clear. Just take any kind of resin, cut up any kind of fiberglass into very small pieces and mix it with the resin, and add hardener. It makes the resin strong and thick, and it comes out clear, not black/gray.

[SkimNate]

you know what? I got an old, banged up woody laying around and my little bro needs a decent board to learn on.

hm this should definitely be on FAQ. J-Gordon da man.

[Jim Gordon]

This belonged to the King (Elvis Presley) It got broken during the Santa Cruz quake of 89. I did a fiberglass repair on it, it has nothing to do with skims, just something I thought you might like to see. This is a chess piece (king) that the king owned.

http://i174.photobucket.com/albums/w113/J-gordon/7-7-200890514AM.jpg

[Jim Gordon]

you know what? I got an old, banged up woody laying around and my little bro needs a decent board to learn on.

hm this should definitely be on FAQ. J-Gordon da man.

Thanks SkimNate, I hope this thread helps you guys get your woodskim back into the water.

[RexSkimmer]

yeah this should be in the FAQ

[Jim Gordon]

There should be a permanent section on how to fix your foam or wood skimboard. What do you think, Aaron? If you like, you can use mine for the wood. Then all you would need is one for foam. If I had time, I would make one on how to fix a foam skim. Maybe someone else could, or maybe you have an old thread or some posts you could use?

[Jim Gordon]

I'm still hearing guys riding rails without a cross pipe. Besides damaging their boards, they are now getting their toes and fingers caught in the end pipes. If you're not sure what an end pipe is, here's a pix of a rail with an end pipe. This rail has only one, but I think you should put one on both ends. Anyway check out the pix.

http://i174.photobucket.com/albums/w113/J-gordon/DSCF0021-1.jpg

http://i174.photobucket.com/albums/w113/J-gordon/DSCF0019-1.jpg

[ghostsushi]

you are seriously one of the coolest/nicest guys on here. you have the most informative and helpful posts/threads and are always looking out for ppl who you suspect might be having issues.
i dont even ride wood boards or flatland, but thanks for bein on the somb. you single handedly bring it up like six notches.

[Jim Gordon]

Thanks. When things slow down, I'll try to make a thread for foam boards. I don't make foam skims anymore, but I still know how to fix them......;)

[Mapdash]

We will definitely add this to the old thread FAQ section.

thx jgordon.